| 軟件簡介： |
摘 要
根據對河北省唐山市馬蘭莊鐵礦礦石性質的研究結果以及對類似選廠的考察，設計馬蘭莊鐵礦選礦廠。該設計為一次建廠，建廠規模為年處理量60萬噸原礦石，根據地形考察報告設計為依山坡建廠，破碎位于同一等高線，主廠房依山坡地勢而建。礦石為中等硬度，原礦最大粒度為500mm，含水量為2%，含泥量小于1%。采礦廢石混入10%。密度3.26噸/立方米，松散度1.5。采用三段一閉路破碎流程。為了達到更好的選礦效果，采用階段磨礦階段選別的流程。原礦品位30%，經過四次磁選后精礦品位可達到66%，回收率為85%，產率為38.64%?？偼顿Y為3430.76萬元，預計投資回收期為0.22年。
關鍵詞：馬蘭莊鐵礦，磨礦，磁選
Abstract
According to the inspection of Malanzhuang iron ore in Tangshan, Hebei Province, nd the nature of the findings of similar election plant inspection, design Malanzhuang iron ore concentrator. The design for a construction, construction of the largest of the handling capacity of 600,000 tons of ore, according to topography inspection report is designed to build factories on the slope, broken in the same contour, the main plant built by a mountain slope potential. Ore for the middle hardness, the largest ore for the size 500 mm, the water content of 3 percent, with mud in less than one percent. Mining waste rock mixed with 10 percent. Density of 3.26 t / cubic meters, 1.5 degrees loose. Using a three-house broken processes. In order to achieve better results processing, grinding stage by stage another election process. Ore grade of 30 percent, after four magnetic separation concentrate grade can be achieved after the 66 percent response rate was 85 percent, the yield was 38.64 percent. This design is expected to total investment of about 38.3533 million yuan, the payback period is 1.12 years.
Keyword: The iron ore of Malanzhuang , Grinding, Magnetic, Process, The building of factories
目錄
摘 要 I
Abstract II
1 引言 1
2 礦石性質的分析 2
3 選礦工藝流程的選擇與計算及工作制度生產能力的確定 3
3.1確定工作制度 3
3.2破碎篩分流程的選擇與計算 3
3.2.1計算破碎車間生產能力 3
3.2.2計算總破碎比及分配各段破碎比 3
3.2.3計算各段產物的最大粒度 4
3.2.4計算各段破碎機的排礦口寬度 4
3.2.5確定篩子的篩孔尺寸和篩分效率 5
3.2.6計算各段產物的礦量和產率 5
3.2.7破碎篩分設備的選擇與計算 5
3.2.7.1粗碎設備 5
3.2.7.2中碎設備 8
3.2.7.3細碎預先及檢查篩分設備 9
3.2.7.4細碎設備 11
3.3磨礦選別流程的選擇計算 13
3.3.1數質量流程計算 13
3.3.1.1磁滑輪的計算 15
3.3.1.2計算第一段磨礦的礦量、產率 15
3.3.1.3選別流程的計算 15
3.3.2礦漿流程的計算 20
3.4磨礦選別主要設備的選擇計算 26
3.4.1磁滑輪的選擇與計算 26
3.4.2一段磨礦設備的選擇計算 26
3.4.3分級機的選擇計算 28
3.4.4二段磨礦設備的選擇計算 29
3.4.5細篩的選擇計算 30
3.4.6磁選設備的選擇 31
4 主要輔助設備的選擇與計算 32
4.1原礦倉的選擇計算 32
4.2原礦倉下給礦機的選擇計算 33
4.3粉礦倉的選擇計算 33
4.4粉礦倉下給礦機的選擇 34
4.5起重設備的選擇計算 34
4.6過濾機的選擇計算 34
4.7真空泵的選擇 35
4.8砂泵的選擇 35
4.9膠帶運輸機的選擇與計算 35
5 生產過程概述 36
6 選礦廠廠址選擇和設備配置 38
6.1選礦廠廠址的選擇 38
6.2選礦廠車間布置和設備配置的特點 38
7 礦山環保與安全 39
7.1環境保護 39
7.2安全 39
8 選礦廠勞動崗位定員 40
9 選礦廠的技術經濟分析 41
9.1選廠工藝投資概算 41
9.1.1設備概算價值 41
9.1.2工藝金屬結構概算價值 42
9.1.3工藝管道概算價值 42
9.2選礦廠基建投資概算 43
9.2.1廠各部門投資 43
9.3選礦技術經濟指標計算 43
9.3.1精礦設計成本的計算 43
9.3.2選礦加工費的計算 44
9.4經濟效果評定 44
9.4.1選礦加工費的計算 44
9.4.2銷售利潤 45
9.4.3經濟分析（靜態法） 45
10 結論 47
10.1結論 47
參考文獻 48
謝辭 49
|
發表評論 
